Testing CC2531

[Corbomit]

Too bad, it seems not to work with a CC2531, neither on Mac, Raspian nor Debian.

The Dongle is found: [ 3.273108] usb 1-1.2: new full-speed USB device number 4 using dwc_otg [ 3.425810] usb 1-1.2: New USB device found, idVendor=0451, idProduct=16ae [ 3.436546] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.451040] usb 1-1.2: Product: CC2531 USB Dongle [ 3.459365] usb 1-1.2: Manufacturer: Texas Instruments

$ python2.7 cc_info.py -p /dev/ttyACM0 ERROR: The chip is not responding. Check your connection and/or wiring! $

The Sketch was compiled with Arduino IDE 1.0.5.

TX+RX just flashes shortly on the Leonardo (the internal LED does not) and then the Error Message appears in the Terminal. Nothing more.

How can I help ?

[Ingramz]

I bought one of the sticks as well and it did not work for me either. What finally let me flash it was https://github.com/RedBearLab/CCLoader on windows with prebuilt exe, arduino leonardo and a level shifter (not voltage divider) to safely interface with the stick.

I am not trying to discourage using CCLib, just that this might help get the ball rolling.

[janinge]

Works fine here on macOS 10.13.4, with a Arduino Due (so no voltage divider, and the native USB port with SerialUSB).

./cc_info.py -p /dev/cu.usbmodem14921 INFO: Found a CC2531 chip on /dev/cu.usbmodem14921

Chip information: Chip ID : 0xb524 Flash size : 256 Kb Page size : 2 Kb SRAM size : 8 Kb USB : Yes

Device information: IEEE Address : 00124b000e89 PC : 0000

Debug status: [ ] CHIP_ERASE_BUSY [ ] PCON_IDLE [X] CPU_HALTED [ ] PM_ACTIVE [ ] HALT_STATUS [ ] DEBUG_LOCKED [X] OSCILLATOR_STABLE [ ] STACK_OVERFLOW

Debug config: [ ] SOFT_POWER_MODE [ ] TIMERS_OFF [X] DMA_PAUSE [X] TIMER_SUSPEND

[balonchiks]

the chip is being detected properly (same as in the reply above), but when flashing it gives out the following error on MacOS 10.13.4 for me:

ERROR: Flash verification error on offset 0x0000

INFO: Found a CC2531 chip on /dev/cu.wchusbserial14110

Chip information:
      Chip ID : 0xb524
   Flash size : 256 Kb
    Page size : 2 Kb
    SRAM size : 8 Kb
          USB : Yes
Sections in CC2531ZNP-Pro-Secure_LinkKeyJoin_mod.hex:

 Addr.    Size
-------- -------------
 0x0000   8176 B 
 0x1ff6   10 B 
 0x3fff0   1 B 
 0x2000   239616 B 

This is going to OVERWRITE the chip. Are you sure? <y/N>:  y

Flashing:
 - Flashing 4 memory blocks...
 -> 0x0000 : 8176 bytes 
    Progress 0%...  ERROR: Flash verification error on offset 0x0000

Any idea what can it be?

[miwinski]

I understand this post is few months old but I've just hit same issue as @balonchiks. Solved it by adding --erase at the end of cc_write.py command (I believe -e would also work as it clearly says it in the official instuction. Flashed CC2531 with Arduino Uno with no resistors.

[Donderda]

Hi together! How did you wire your UNO? If I try to run the cc_info.py, I get only "No chip found. Check your connection and/or wiring". My CC2531 gets green for a short time. But nothing else happen :(

[Donderda]

I bought one of the sticks as well and it did not work for me either. What finally let me flash it was https://github.com/RedBearLab/CCLoader on windows with prebuilt exe, arduino leonardo and a level shifter (not voltage divider) to safely interface with the stick.

I am not trying to discourage using CCLib, just that this might help get the ball rolling.

Where did you get the bin from?

[Ingramz]

Where did you get the bin from?

It's right there, in a folder named Windows

[rkantos]

Works fine here on macOS 10.13.4, with a Arduino Due (so no voltage divider, and the native USB port with SerialUSB).

How and which pins did you use with your Arduino Due and the CC2531?

[ReDetection]

@balonchiks I was able to workaround this by lowering UART speed to 9600baud. Dunno why this worked ¯_(ツ)_/¯