netifd
netifd copied to clipboard
openwrt
netifd dont include dynamic vlans from hostapd
i have the problem, that the luci wireless page dont show any stations connected to dynamic vlans on wpa2 enterprise or wpa2 personal ppsk. i traced it back to the luci code getting a empty vlan list and therefore dont even look at the vlans. the empty vlan list i traced back again first to ubus, which showed empty vlan list (ubus -v call network.wireless status), and this back to netifd, which dont consider the dynamicaly created vlans from hostapd and therefore the ubus vlan list is empty and therefore luci dont check for any stations on dynamic vlan networks.
here is the output of ubus -v call network.wireless status:
"radio0": {
"up": true,
"pending": false,
"autostart": true,
"disabled": false,
"retry_setup_failed": false,
"config": {
"path": "platform/soc/a000000.wifi",
"channel": "1",
"band": "2g",
"htmode": "HT20",
"cell_density": 0,
"country": "DE"
},
"interfaces": [
{
"section": "wifinet3",
"ifname": "phy0-ap0",
"config": {
"mode": "ap",
"ssid": "HSZ",
"encryption": "wpa2+ccmp",
"auth_server": [
"127.0.0.1"
],
"auth_secret": "testing123",
"dynamic_vlan": 1,
"auth_port": 1812,
"vlan_file": "/etc/config/phy0-ap1.hostapd.vlan",
"vlan_bridge": "br-vlan",
"eap_reauth_period": 0,
"mode": "ap",
"network": [
"lan"
]
},
"vlans": [
],
"stations": [
]
},
{
"section": "wifinet4",
"ifname": "phy0-ap1",
"config": {
"mode": "ap",
"ssid": "HSZLegacy",
"encryption": "psk2+ccmp",
"key": "blablabla",
"wpa_psk_file": "/etc/config/wpa_psk_file",
"vlan_bridge": "br-vlan",
"vlan_file": "/etc/config/phy0-ap0.hostapd.vlan",
"dynamic_vlan": 1,
"mode": "ap",
"network": [
"lan"
]
},
"vlans": [
],
"stations": [
]
}
]
},
"radio1": {
"up": true,
"pending": false,
"autostart": true,
"disabled": false,
"retry_setup_failed": false,
"config": {
"path": "platform/soc/a800000.wifi",
"channel": "36",
"band": "5g",
"htmode": "VHT80",
"cell_density": 0,
"country": "DE"
},
"interfaces": [
{
"section": "default_radio1",
"ifname": "phy1-ap0",
"config": {
"mode": "ap",
"ssid": "FRITZ!Box 7530 GL",
"encryption": "psk2",
"key": "blablabla",
"ieee80211r": true,
"ft_over_ds": false,
"ft_psk_generate_local": true,
"maclist": [
"96:46:27:6E:70:1F"
],
"network": [
"unten"
],
"mode": "ap"
},
"vlans": [
],
"stations": [
]
},
{
"section": "wifinet2",
"ifname": "phy1-ap1",
"config": {
"mode": "ap",
"ssid": "HSZ",
"encryption": "wpa2+ccmp",
"auth_server": [
"127.0.0.1"
],
"auth_port": 1812,
"auth_secret": "testing123",
"dynamic_vlan": 1,
"vlan_bridge": "br-vlan",
"vlan_file": "/etc/config/phy1-ap1.hostapd.vlan",
"eap_reauth_period": 0,
"mode": "ap",
"network": [
"lan"
]
},
"vlans": [
],
"stations": [
]
}
]
}
}
the output of iwinfo:
phy0-ap0 ESSID: "HSZ"
Access Point: DC:15:C8:3C:F8:06
Mode: Master Channel: 1 (2.412 GHz) HT Mode: HT20
Center Channel 1: 1 2: unknown
Tx-Power: 20 dBm Link Quality: unknown/70
Signal: unknown Noise: -98 dBm
Bit Rate: unknown
Encryption: WPA2 802.1X (CCMP)
Type: nl80211 HW Mode(s): 802.11b/g/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy0
phy0-ap0.10 ESSID: unknown
Access Point: DE:15:C8:3C:F8:06
Mode: Master (VLAN) Channel: 1 (2.412 GHz) HT Mode: HT20
Center Channel 1: 1 2: unknown
Tx-Power: 0 dBm Link Quality: 45/70
Signal: -65 dBm Noise: -98 dBm
Bit Rate: 144.4 MBit/s
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11b/g/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy0
phy0-ap0.5 ESSID: unknown
Access Point: DE:15:C8:3C:F8:06
Mode: Master (VLAN) Channel: 1 (2.412 GHz) HT Mode: HT20
Center Channel 1: 1 2: unknown
Tx-Power: 0 dBm Link Quality: unknown/70
Signal: unknown Noise: -98 dBm
Bit Rate: unknown
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11b/g/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy0
phy0-ap0.69 ESSID: unknown
Access Point: DE:15:C8:3C:F8:06
Mode: Master (VLAN) Channel: 1 (2.412 GHz) HT Mode: HT20
Center Channel 1: 1 2: unknown
Tx-Power: 0 dBm Link Quality: unknown/70
Signal: unknown Noise: -98 dBm
Bit Rate: unknown
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11b/g/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy0
phy0-ap0.72 ESSID: unknown
Access Point: DE:15:C8:3C:F8:06
Mode: Master (VLAN) Channel: 1 (2.412 GHz) HT Mode: HT20
Center Channel 1: 1 2: unknown
Tx-Power: 0 dBm Link Quality: unknown/70
Signal: unknown Noise: -98 dBm
Bit Rate: unknown
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11b/g/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy0
phy0-ap0.80 ESSID: unknown
Access Point: DE:15:C8:3C:F8:06
Mode: Master (VLAN) Channel: 1 (2.412 GHz) HT Mode: HT20
Center Channel 1: 1 2: unknown
Tx-Power: 0 dBm Link Quality: unknown/70
Signal: unknown Noise: -98 dBm
Bit Rate: unknown
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11b/g/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy0
phy0-ap1 ESSID: "HSZLegacy"
Access Point: DE:15:C8:3C:F8:06
Mode: Master Channel: 1 (2.412 GHz) HT Mode: HT20
Center Channel 1: 1 2: unknown
Tx-Power: 20 dBm Link Quality: unknown/70
Signal: unknown Noise: -98 dBm
Bit Rate: unknown
Encryption: WPA2 PSK (CCMP)
Type: nl80211 HW Mode(s): 802.11b/g/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy0
phy0-ap1.10 ESSID: unknown
Access Point: DC:15:C8:3C:F8:06
Mode: Master (VLAN) Channel: 1 (2.412 GHz) HT Mode: HT20
Center Channel 1: 1 2: unknown
Tx-Power: 0 dBm Link Quality: unknown/70
Signal: unknown Noise: -98 dBm
Bit Rate: unknown
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11b/g/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy0
phy0-ap1.5 ESSID: unknown
Access Point: DC:15:C8:3C:F8:06
Mode: Master (VLAN) Channel: 1 (2.412 GHz) HT Mode: HT20
Center Channel 1: 1 2: unknown
Tx-Power: 0 dBm Link Quality: unknown/70
Signal: unknown Noise: -98 dBm
Bit Rate: unknown
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11b/g/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy0
phy0-ap1.69 ESSID: unknown
Access Point: DC:15:C8:3C:F8:06
Mode: Master (VLAN) Channel: 1 (2.412 GHz) HT Mode: HT20
Center Channel 1: 1 2: unknown
Tx-Power: 0 dBm Link Quality: unknown/70
Signal: unknown Noise: -98 dBm
Bit Rate: unknown
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11b/g/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy0
phy0-ap1.72 ESSID: unknown
Access Point: DC:15:C8:3C:F8:06
Mode: Master (VLAN) Channel: 1 (2.412 GHz) HT Mode: HT20
Center Channel 1: 1 2: unknown
Tx-Power: 0 dBm Link Quality: unknown/70
Signal: unknown Noise: -98 dBm
Bit Rate: unknown
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11b/g/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy0
phy0-ap1.80 ESSID: unknown
Access Point: DC:15:C8:3C:F8:06
Mode: Master (VLAN) Channel: 1 (2.412 GHz) HT Mode: HT20
Center Channel 1: 1 2: unknown
Tx-Power: 0 dBm Link Quality: unknown/70
Signal: unknown Noise: -98 dBm
Bit Rate: unknown
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11b/g/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy0
phy1-ap0 ESSID: "FRITZ!Box 7530 GL"
Access Point: DC:15:C8:3C:F8:07
Mode: Master Channel: 36 (5.180 GHz) HT Mode: VHT80
Center Channel 1: 42 2: unknown
Tx-Power: 23 dBm Link Quality: 10/70
Signal: -100 dBm Noise: -110 dBm
Bit Rate: 237.8 MBit/s
Encryption: WPA2 PSK (CCMP)
Type: nl80211 HW Mode(s): 802.11ac/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy1
phy1-ap1 ESSID: "HSZ"
Access Point: DE:15:C8:3C:F8:07
Mode: Master Channel: 36 (5.180 GHz) HT Mode: VHT80
Center Channel 1: 42 2: unknown
Tx-Power: 23 dBm Link Quality: unknown/70
Signal: unknown Noise: -110 dBm
Bit Rate: unknown
Encryption: WPA2 802.1X (CCMP)
Type: nl80211 HW Mode(s): 802.11ac/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy1
phy1-ap1.10 ESSID: unknown
Access Point: DE:15:C8:3C:F8:07
Mode: Master (VLAN) Channel: 36 (5.180 GHz) HT Mode: VHT80
Center Channel 1: 42 2: unknown
Tx-Power: 0 dBm Link Quality: unknown/70
Signal: unknown Noise: -110 dBm
Bit Rate: unknown
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11ac/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy1
phy1-ap1.5 ESSID: unknown
Access Point: DE:15:C8:3C:F8:07
Mode: Master (VLAN) Channel: 36 (5.180 GHz) HT Mode: VHT80
Center Channel 1: 42 2: unknown
Tx-Power: 0 dBm Link Quality: unknown/70
Signal: unknown Noise: -110 dBm
Bit Rate: unknown
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11ac/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy1
phy1-ap1.69 ESSID: unknown
Access Point: DE:15:C8:3C:F8:07
Mode: Master (VLAN) Channel: 36 (5.180 GHz) HT Mode: VHT80
Center Channel 1: 42 2: unknown
Tx-Power: 0 dBm Link Quality: unknown/70
Signal: unknown Noise: -110 dBm
Bit Rate: unknown
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11ac/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy1
phy1-ap1.72 ESSID: unknown
Access Point: DE:15:C8:3C:F8:07
Mode: Master (VLAN) Channel: 36 (5.180 GHz) HT Mode: VHT80
Center Channel 1: 42 2: unknown
Tx-Power: 0 dBm Link Quality: unknown/70
Signal: unknown Noise: -110 dBm
Bit Rate: unknown
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11ac/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy1
phy1-ap1.80 ESSID: unknown
Access Point: DE:15:C8:3C:F8:07
Mode: Master (VLAN) Channel: 36 (5.180 GHz) HT Mode: VHT80
Center Channel 1: 42 2: unknown
Tx-Power: 0 dBm Link Quality: unknown/70
Signal: unknown Noise: -110 dBm
Bit Rate: unknown
Encryption: unknown
Type: nl80211 HW Mode(s): 802.11ac/n
Hardware: embedded [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy1
as you can see, the vlan interfaces are there, they are just not part of the vlan list and therefore not picked up by luci
thx
Same issue here. If I am not mistaken, in https://github.com/openwrt/netifd/blob/68c8a4f94cd3cfd654a52cbc8b57c5c9d99640dd/config.c#L159 netifd collects interface information, but here it only considers the uci config files and this configuration will not include enough information to infer all the correct interface names, nor should it try to.
The second place netifd seems to look for information is in https://github.com/openwrt/netifd/blob/68c8a4f94cd3cfd654a52cbc8b57c5c9d99640dd/config.c#L675. Here I am less sure. To me, it looks like it looks through what you should also get using ubus -v call service get_data for entries called wifi-iface. However, even with just a regular configuration, I do not see entries like that here. I may be completely wrong here, or it might be for a type of configuration I simply do not have. I don't know.
In essence, to me it looks like ifnetd only looks at configuration files while looking for wireless devices, and not at actual existing devices and it does not support all possible configuration options (again, I think it really shouldn't). Instead, it likely should get the list of devices from something like ubus call iwinfo devices. Question to the devs: would that work?
